Wednesday, February 23, 2022

Making an experimental V shaped electric guitar part 2/2

 































Tools and materials:

Metallic guitar pickup

Block plane

No4 hand plane

Chisel set

Jointer planer

Table saw

Bandsaw

Cordless drill

Rotary tool

Volume pot

Output jack

Control knob

Belt sander

Flat rasp

Round rasp

Flat file

Plunge router

Trim router

Angle grinder

Round file

Spoke shave

Forstner bit set

Soldering kit

Fret wire

Tune-o-matic Bridge & Tailpiece


In this video I complete the making of the DIY V shaped electric guitar I started on the previous video. 


Special thanks to:

a.) stewmac for the online fret calculator: https://www.stewmac.com/fret-calculator/

b.) www.seymourduncan.com for the wiring diagrams

Both sites are really helpful and I am really grateful for the info they provide. 


At this point I started making the cavities for the electronics. I used my router, chisels and forstner bits for the job. 


I then drilled the holes on the pickguard and installed the bridge. The bridge has some metal inserts but I didn’t have any so I placed it straight in the wood. Although this was not the proper way to do it. 


I then did some fine tunings on the pickguard and polished it. 


I coloured the guitar with water based dye. I first applied the red coat. Then I added the black. I used a wet rag to create the gradient effect ( sunburst ). I then finished the body with clear water based varnish. 


At this point I started shaping the neck with rasps, files and a spokeshave. 


I made the fretboard. My scale was 443mm from nut to nut. I used an online fret calculator to measure my fret positions. 


While the fretboard glue was drying I did all the soldering stuff. 


I trimmed the fretboard flush and started installing the frets. I trimmed them flush with a file and added a drop of glue from the sides. Then I levelled the frets and polished them. 


Finally I made the nut and bridge. And added the strings.


My little guitar was ready. It was a ton of fun to make. But that was it, see you soon with a new project video.


Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.

Friday, February 18, 2022

Making an experimental V shaped electric guitar part 1/2

 




















Tools and materials:

Metallic guitar pickup

Block plane

No4 hand plane

Chisel set

Jointer planer

Table saw

Bandsaw

Cordless drill

Rotary tool

Volume pot

Output jack

Control knob

Belt sander

Flat rasp

Round rasp

Flat file

Plunge router

Trim router

Angle grinder

Round file

Spoke shave


In this video I begin to make a DIY V shaped electric guitar out of beech wood and metal.


I begun by making a full size template out of cardboard. 


I then planed my wood and cut it roughly n the bandsaw.


I then glued the body pars together. 


Next I sanded the body and added a round over with the router. 


Next I cut the basic shape of the neck. 


I routed out the neck joint on the body. I used a chisel and plane to make it fit right. 


Then I routed and chiseled the pickup pocket. 


Out of a sheet of metal I cut my metal parts with the angle grinder. I then fine tuned them with files. 


At this point I stopped. The build will continue and finish on the next video. 


I hope you liked it so far because that was it, see you soon with the next and final part. 



Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.

Friday, February 11, 2022

Tips for making wooden toys

 
























Tools and materials I propose:

Scroll saw

Rotary tool

Hole saw

Cordless drill

Block plane

Plunge router

Pyrography Pen Wood Burning Kit

Buffing kit

Alcohol based markers

Lathe

Wood turning tools set

Chuck kit

Table saw

Drill press

Bandsaw



In this video I tried to show a few tips and tricks for DIY woodworkers who like to make toys.


In the video I show some simple and some more complicated stuff. You should keep what you need and what you feel is useful for your style of toy making.


I hope you found this video useful. See you soon with a new project video. 



Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.

Friday, February 4, 2022

How to start wood carving with hand tools

 





















Tools and materials I propose:

Flexcut starter carving set

PFEIL Carving Set

Carving mallet

Tormek T8 Sharpening System

Tormek Hand Tool Sharpening Kit

Chisel set


I tried to make a video with all the basic information you need  in order to start wood carving with hand tools. 


In the video you’ll find information about tools and how to use them. 


You will also find information about sharpening the tools, various types of woods and information a bout the wood in general. 


I hope you’ll find the video useful. 


Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.

Thursday, January 27, 2022

How to make a kuksa on the lathe - Woodturning

 

























Tools and materials I propose:

Lathe

Wood turning tools set

Chuck kit

Tormek T8 Sharpening System

Tormek Woodturner’s Kit

Table saw

Flexcut starter carving set

Pyrography Pen Wood Burning Kit

Buffing kit


In this video I make a kuksa mug on the lathe. Usually this is made using hand carving knives. But I thought it would be a good challenge to make it on a lathe. It actually involved a few really interesting techniques. I made it out of basswood.


I begun by preparing my stock on the planer and table saw. 


With this this technique I will actually have two blanks after the first stage of woodturning. 


After preparing my two blanks I added a few guide lines. I also had to consider the pieces of wood that would had to be removed because of tool marks from the chuck and tailstock.


To glue the two pieces together I added a piece of paper in between. This would help me separate the pieces later on. 


At this point I started turning the outer shape of my kuksa. Once I was ready I split the two blanks in half with a chisel. 


The I took one blank and put it on a screw chuck to make a tenon on the other side. 


I then chucked it on the jaws and hollowed it out with a bowl gouge. 


To clean the bottom I used my bowl bottom cleaning jaws. 


Next I did some fine tunings on the shape with a carving knife. 


I carved a flower on it’s handle and used my wood burner to decorate it. 


Finally I buffed the mug with carnauba wax.


And my kuksa was ready. 


It was a really interesting project, but that was it. 


See you soon with a new project video. 


Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.

Thursday, January 20, 2022

A few interesting pyrography techniques and woodturning drink coasters

 


























Tools and materials I propose:

Pyrography Wood Burning Tips

Pyrography Pen Wood Burning Kit

Soldering iron

Alcohol based markers

Lathe

Wood turning tools set

Chuck kit

Tormek T8 Sharpening System

Tormek Woodturner’s Kit

Bandsaw

Buffing kit


In this video I make a few drink coasters out of basswood. This was a nice excuse to try out a few simple but really cool 

wood burning techniques. 


I first turned my coasters on the lathe. I got three coasters from one blank. This was mostly bowl gouge work. 


I cleaned the bottom with my bowl bottom jaws. I made the bottom a bit concave so the coaster can sit nicely on a flat surface. 


In the first technique I created shading by adding burned dots. I set my burning station at a high temperature and went for it. To color my work I used ink based markers. They work really nice on wood and are very easy to use. 


For the second technique I changed the tip on my wood burner and added shading with a more traditional manner. I went slow here so I reduced the temperature of my burner. When colouring I like to leave the wood as my highest light. Especially on basswood this works really nicely.


On the third technique I used the classic soldering iron type of burner. By changing tips I tried to give different textures to my work.


I finished all my coasters with carnauba wax on my buffing wheel.


I am really happy with these three new techniques. But that was it. See you soon with a new project video. 


Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.